Guide

How to Cut Galvanized Pipe with a Sawzall

Updated on · By the Raw Metal Edge team

Cut galvanized pipe with a Sawzall using a 14 TPI metal blade, a clamped pipe, and a slow, steady stroke through the wall. Mark the line all the way around, cut just outside it, then file the burr and chase the threads before you fit the new piece.

On this page (7 sections)
  1. What blade do you need to cut galvanized pipe?
  2. How do you set up the pipe before cutting?
  3. How to cut galvanized pipe with a Sawzall, step by step
  4. How do you keep the cut square and clean?
  5. What should you know about the zinc coating?
  6. How do you handle tight spots and mounted pipe?
  7. Which saw and blade should you pick for the job?

Cut galvanized pipe with a Sawzall using a 14 TPI metal blade, a clamped pipe, and a slow, steady stroke through the wall. Mark the line all the way around, cut just outside it, then file the burr and chase the threads before you fit the new piece.

Galvanized pipe is steel under a zinc skin, so it cuts like any other steel tube. The job goes well when you choose the right blade and keep the pipe from shaking while the saw runs.

What blade do you need to cut galvanized pipe?

Use a 14 TPI bi-metal blade made for metal. The tooth count matches the wall thickness of standard galvanized water pipe, so the teeth clear the chips instead of packing up.

A coarse wood blade will bounce off the zinc and burn through its own teeth. A fine 18 TPI blade cuts slower and heats faster on pipe this thick.

The 14 TPI range is the middle ground that keeps the cut clean and the blade cool.

The Milwaukee Tool 6" 14 TPI The Torch blade set is built for this. The 6-inch length fits inside a tight joist bay or under a sink, and the alloy steel body flexes when the pipe is close to a wall.

The blade is 1 inch tall for straight, fast cutting, and the heat treating process is meant to extend blade life.

Match the blade length to the pipe. A 6-inch blade handles pipe up to about 4 inches across; longer blades reach bigger mains but flex more in a short stroke.

Keep a spare on hand, since zinc and steel dull a blade faster than clean steel alone.

How the tooth count affects the cut

Fourteen teeth per inch leaves enough gullet between the teeth to carry chips out of a steel wall. Go coarser and the blade catches on the pipe wall and chatters.

Go finer and the chips clog the teeth, so the blade rubs instead of cuts and heats up fast.

How do you set up the pipe before cutting?

Shut off the water, drain the line, and clamp the pipe on both sides of your mark. A pipe that moves under the blade throws off the cut and can bind the saw.

Close the nearest valve and open a faucet below the cut to drain the section. Water left in the pipe sprays out as the blade breaks through and makes the cut harder to control.

Support the pipe close to the cut with a pipe vise or a clamp on each side. If the pipe is already mounted, brace it against the framing so it can't twist.

Wrap the jaws in a rag if you want to protect the zinc.

Measure from a fixed point and mark the cut line with a wrap-around square or a strip of tape. A line that circles the whole pipe lets you check square from any angle as you cut.

Leave the mark itself visible so you can glance at it mid-cut without stopping the saw.

How to cut galvanized pipe with a Sawzall, step by step

Start the blade on the mark at low speed and work around the pipe, rather than pushing straight through one side. A pipe cut goes faster when the blade stays square to the wall.

  1. Put on safety glasses and gloves, and clear the area below the cut.
  2. Mark the cut line all the way around the pipe.
  3. Set the shoe flat against the pipe just outside the mark.
  4. Start the saw slowly and let the blade bite into the zinc.
  5. Follow the line around the pipe, keeping light, even pressure.
  6. Finish the cut and check the end with a square.

Keep the saw body steady and move it with the blade, not against it. Let the teeth cut; pushing harder heats the blade and can crack the zinc around the cut.

Setting the speed and stroke

Run the saw at a moderate speed on pipe. Full speed on thin-wall galvanized tube causes chatter and a ragged edge.

A slow, steady stroke with the shoe pressed flat gives the cleanest line.

The DeWalt DWE305 has a variable speed trigger that lets you start slow and speed up once the blade is seated. Its 1-1/8 inch stroke clears chips from the cut and its 12 amp motor holds speed through thicker pipe.

The 4-position blade clamp also lets you turn the blade for flush cuts where the pipe sits against a surface.

If you cut pipe often and away from outlets, the Milwaukee M18 FUEL Sawzall runs on battery and its lever blade clamp makes swaps quick. Its built-in LED light helps under a sink or in a dim basement.

The metal reinforced battery connection is built to hold the pack tight over the life of the tool.

How do you keep the cut square and clean?

Keep the shoe flat and check the line every inch or so. The most common mistake is tilting the saw, which leaves an angled end that won't thread or fit a coupling.

Watch the blade from the side as it goes around. If it drifts off the line, ease off the trigger and steer back with light pressure rather than forcing it.

Rotate the pipe if you can, so you always cut on the top where you can see the mark.

Let the blade finish the last bit at low speed. Breaking through at full speed can snag the pipe and bend the blade.

A square end matters more than a fast cut here, because an angled end will not start in a die head straight.

Cleaning up the cut end

Run a half-round file around the inside and outside edge to knock off the burr. A burr left on the end catches the threads and can stop a fitting from seating.

Wipe the end clean and dry. Galvanized pipe loses its zinc coating at the cut, so paint or seal the bare edge if the line sits outdoors or in a damp spot.

Then chase or cut new threads as your repair needs.

What should you know about the zinc coating?

Cutting exposes bare steel at the end, so seal it after the cut. The zinc coating protects the pipe from rust, and the fresh edge no longer has that layer.

Don't grind or sand the whole pipe to remove the coating. Cut as normal, file the edge, and coat only the bare ring at the end with a zinc-rich paint or pipe sealant.

Wear eye protection and a dust mask when filing or cutting indoors. The dust and chips from a galvanized cut are best swept up rather than blown around.

Sweep them into a bag rather than leaving them on a floor where someone walks barefoot.

How do you handle tight spots and mounted pipe?

Cut in short strokes and let the blade length do the work when space is tight. A 6-inch blade fits where a longer one hits the wall or framing.

Hold the saw at an angle that keeps the shoe on the pipe and the blade clear of nearby surfaces. If the pipe sits against a stud, cut from the open side and finish the last bit carefully so the blade doesn't dig into the wood.

On a pipe running along a joist, the short Torch blade is the difference between a clean cut and a blade pinned against lumber.

For cuts in a crawlspace or under a cabinet, a cordless saw with a light makes the line easier to follow. The same approach works when you cut exhaust pipe with a Sawzall: clamp it, mark it, and cut slow.

If you also run PVC lines nearby, our guide to how to cut PVC pipe with a reciprocating saw covers the blade and speed for plastic.

Which saw and blade should you pick for the job?

Pick the 14 TPI metal blade for the cut and a variable speed saw for control. For most homeowners, a corded reciprocating saw plus the Milwaukee Torch blade covers standard galvanized repairs.

Choose the corded DeWalt if you have an outlet and want steady power for thicker pipe. Choose the Milwaukee M18 FUEL if you work in basements, crawlspaces or outdoors where a cord gets in the way.

Choose the Milwaukee 14 TPI Torch set when you need a short blade for pipe close to walls. A 14 TPI metal blade on a clamped pipe is the whole recipe for a square cut.

If you plan to cut concrete or masonry on the same job, read can a reciprocating saw cut concrete before you load the wrong blade. And if you want a saw built for metal work, compare the best reciprocating saws for cutting metal.

To sum up how to cut galvanized pipe with a Sawzall: shut off and drain the line, clamp the pipe, mark a full ring, and cut slow with a 14 TPI blade. File the burr and seal the bare edge, and the repair piece will fit square and clean.

Frequently asked questions

Will a Sawzall cut galvanized steel pipe?

Yes. Galvanized pipe is steel with a zinc coating, and a reciprocating saw with a 14 TPI metal blade cuts it.

Use low speed, keep the shoe flat on the pipe, and let the blade do the work.

How long does it take to cut a half-inch galvanized pipe?

A half-inch pipe usually takes under a minute with a sharp 14 TPI blade and a clamped pipe. Larger pipe and thick walls take longer, so plan on steady pressure rather than forcing the saw.

Do I need to remove the zinc coating before cutting?

No. You can cut through the galvanized layer, but the cut end loses its coating.

Paint or seal the bare edge afterward to slow rust, especially on outdoor or wet lines.

Can I cut galvanized pipe with the water on?

No. Shut off the supply and drain the line first.

Water in the pipe grabs the blade, hides the cut line, and makes a square cut hard to hold.