How to Cut Exhaust Pipe With a Sawzall
Cut exhaust pipe with a Sawzall by clamping the pipe steady, fitting a 14 TPI metal blade, and running the saw at low speed with light pressure. Mark the line all the way around the pipe first so the cut stays square.
On this page (9 sections)
- What do you need before you cut exhaust pipe?
- How do you mark and support the pipe for a square cut?
- Which blade should you use on exhaust pipe?
- How do you make the cut with a Sawzall?
- Why does a Sawzall struggle on some exhaust cuts?
- What saw and blade setup works best?
- How do you finish and check the cut?
- What mistakes should you avoid when cutting exhaust pipe?
- The short version
Cut exhaust pipe with a Sawzall by clamping the pipe steady, fitting a 14 TPI metal blade, and running the saw at low speed with light pressure. Mark the line all the way around the pipe first so the cut stays square.
That order matters more than the saw you own. A steady pipe and the right blade do more for a clean end than a bigger motor, and both are easy to get right before the saw touches metal.
What do you need before you cut exhaust pipe?
You need safe access under the car, a metal-cutting blade, a marker, and something to hold the pipe. Plan the cut position before you lift anything.
Raise the vehicle on rated stands on level ground, never on a jack alone. Wear safety glasses and hearing protection, since a reciprocating saw under a car is loud and throws metal chips.
Clear the area around the cut first. Look for fuel lines, brake lines, wiring, and the fuel tank before the blade goes anywhere near the pipe.
A cheap exhaust cut can turn expensive fast if the blade catches a brake line.
Have a hand file or a flapper disc ready for the burr. A tape measure and a marker let you mark the cut from more than one side, which is how you keep the end square.
How do you mark and support the pipe for a square cut?
Wrap the mark all the way around the pipe and support both sides before cutting. A pipe that sags mid-cut pinches the blade and leaves a ragged edge.
Measure from a fixed point, like a flange or a hanger, rather than eyeballing the length. Mark the line at three or four points around the circumference, then join them with a straight edge or a wrap of tape.
Tape around the pipe at the cut line works well because the edge gives the blade a guide to follow. It also holds the mark visible while you work.
Support the pipe with a stand or a block on each side of the cut. Exhaust pipe is thin and light, and an unsupported section will drop as soon as the blade breaks through.
A floor jack with a block of wood under the pipe is enough to hold it.
Which blade should you use on exhaust pipe?
Use a 14 TPI bi-metal blade made for metal cutting. The tooth count suits thin-wall pipe and tubing, which is what exhaust systems are mostly made of.
A coarse blade grabs thin pipe and shakes it, so avoid wood blades and low tooth counts. A fine blade for thick steel cuts slowly and heats up in pipe this thin.
The 14 TPI range is the middle ground that most exhaust work falls into.
The Milwaukee Tool 6" 14 TPI The Torch is a 6-inch bi-metal blade in a 5-pack, and Milwaukee lists it for cutting pipe, tubing, and channel. The 14 teeth per inch match thin-wall exhaust tube well.

A 6 inch 14 TPI bi-metal blade aimed at pipe and tubing, sold in a 5-pack so you have spares for long systems.
See it on AmazonKeep a spare blade within reach. Exhaust pipe is often dirty and rusty underneath, and a blade that hits a weld or a hanger bracket dulls faster than one cutting clean tube.
If you cut a lot of metal and want to compare saws for it, our roundup of the best reciprocating saws for cutting metal covers the models built for that work.
How do you make the cut with a Sawzall?
Start the saw flat against the pipe and cut with light pressure at low speed. Let the teeth do the work instead of pushing the blade through.
Set the saw to a low speed setting if it has one. High speed on thin metal heats the blade and can burn the teeth, and the cut goes no faster for it.
Rest the saw shoe on the pipe and start the blade just inside the mark. Hold the saw with both hands and keep the blade square to the pipe as it moves around the circumference.
Work slowly around the pipe rather than straight through one side. On a round pipe the blade tends to walk, so follow the tape line and check your position as you go.
Our guide to what angles a reciprocating saw cut explains how the blade behaves when you turn the saw.
Ease off as the blade breaks through so the pipe doesn't drop onto it. If the pipe shifts, stop, reset the support, and start again.
Can you cut exhaust pipe in place under the car?
Yes, most exhaust cuts are made with the pipe still on the car. Support the section you're removing and the section staying, and keep the saw body clear of the floor and the frame.
A reciprocating saw needs room to stroke, so check that the blade and the saw body won't hit the underbody as you move. A shorter blade helps in tight spots over the rear axle or near the fuel tank.
Why does a Sawzall struggle on some exhaust cuts?
Thick flanges, hanger rods, and catalytic converter shells slow a Sawzall down. They're heavier steel than the pipe itself, and a 14 TPI blade works through them slowly.
Stainless systems are tougher than plain steel too. Expect more time and more blade wear, and keep the speed low so the blade doesn't overheat.
Rust and heat shields cause most of the trouble. A shield sitting against the pipe can catch the blade, so check what's around the cut before you start.
Move or peel back anything loose first.
If the blade keeps binding, the pipe is probably pinching it. Stop and reset the support rather than forcing the cut.
A bound blade bends or snaps, and a snapped blade under a car is a real hazard.
What saw and blade setup works best?
A cordless reciprocating saw with a lever blade clamp and a 14 TPI metal blade handles most exhaust jobs. The clamp matters more than the motor size when you're changing blades in a tight space.
The Milwaukee M18 FUEL Sawzall is a bare tool with a brushless motor and a lever-actuated blade clamp for fast changes. It also has a built-in LED light that helps under a dark car.

A brushless cordless Sawzall with a lever blade clamp and an LED light for cutting under the car.
See it on AmazonIt's sold as a bare tool with no battery or charger, so you need a compatible Milwaukee battery and charger already. If you're starting from nothing, price the battery in before you buy.
For mixed work on the same job, the Milwaukee 12 Piece Multi Material set covers wood, plastic, and metal blades in 6-inch and 9-inch lengths. The set's metal blades include 18 TPI blades for pipe and tubing, plus 14 TPI blades for heavier metal.

A 12 piece blade set with 6 and 9 inch metal blades, plus wood and plastic blades for the rest of the job.
See it on AmazonThe set's storage case holds blades up to 9 inches. If you only cut exhaust, a pack of 14 TPI metal blades is the simpler buy; the mixed set makes more sense when the same saw handles hanger brackets and heat shield work too.
How do you finish and check the cut?
File the burr off the end and test fit the joint before you tighten anything. A clean, square end is what makes a sleeve or clamp seal.
Run a hand file around the inside and outside edge of the cut at a slight angle. A flapper disc on a grinder does the same job faster, but keep it light so you don't thin the pipe wall.
Check the end for square with a straight edge. A slanted cut leaves a gap at the joint, and a gap leaks.
Slide the new section or the sleeve into place and check the fit before clamping. If it's tight, dress the edge a little more rather than forcing it.
Then tighten the clamp evenly and check for leaks once the engine runs.
What mistakes should you avoid when cutting exhaust pipe?
The biggest mistakes are pushing the saw too hard, cutting without support, and skipping the mark. Each one costs you a clean end and often a second cut.
Forcing the blade overheats it and bends the cut. Let the saw cut at its own pace and keep the pressure light.
Cutting without support lets the pipe drop and pinch the blade. Support both sides every time, even on a short section.
Skipping the mark and the tape guide is how you end up with a slanted end that won't seal. Mark it fully and follow the line.
Finally, don't cut near fuel or brake lines without checking what's there first. Look before you start the saw.
The short version
The answer to how to cut exhaust pipe with Sawzall comes down to four things: mark the pipe all the way around, support both sides, fit a 14 TPI bi-metal blade, and cut slowly with light pressure. File the burr and test fit before you clamp.
Choose the Milwaukee M18 FUEL Sawzall if you want a cordless saw with a fast lever blade clamp and an LED light for under-car work. Pick the 14 TPI The Torch blades if exhaust pipe is the main job.
Take the 12 Piece Multi Material set when the same saw also handles brackets, shields, and other materials.
If your next cut is plastic rather than steel, our guide to how to cut PVC pipe with a reciprocating saw covers the blade and speed that suit it. And if you're wondering whether the same saw handles masonry, see can a reciprocating saw cut concrete before you try it.
Frequently asked questions
Can a Sawzall cut through a catalytic converter pipe?
Yes, with the right metal blade and patience. Converter shells and hanger rods are thicker than plain pipe, so expect a slower cut and keep the blade speed low to avoid burning the teeth.
Do I need to remove the exhaust from the car before cutting it?
No, most cuts under a car are made in place. Raise the vehicle on safe stands, wear eye and ear protection, and keep the saw clear of fuel lines, brake lines, and wiring before you start.
How much space do I need under the car to run a Sawzall?
Leave enough room to hold the saw with the blade clear of the floor and your arm free to move. The Sawzall body is about 10 inches long, so a few inches of clearance around the cut keeps the stroke from hitting anything.
Will a reciprocating saw leave a burr on exhaust pipe?
Yes, most cuts leave a light burr or a slightly ragged edge. Knock it down with a hand file or a flapper disc before you fit a sleeve or clamp, so the joint seals without leaks.
Should I cut exhaust pipe dry or with lubricant?
Cut dry. Oil on the blade makes the chips clump and can make the blade wander, and exhaust pipe cuts cleanly without coolant.
Brush chips away as you go and check the blade for heat.
About this guide: Our look at cutting exhaust pipe with a reciprocating saw draws on maker specs, materials and what owners report. See how we research.



