Guide

Will a Sawzall Cut 1/4-Inch Steel?

Updated on · By the Raw Metal Edge team

Yes, a Sawzall will cut 1/4-inch steel with a bi-metal metal-cutting blade and a slow, steady stroke. It is thicker than the usual sheet metal job, so expect slower progress, more heat and more blade wear than on 1/8-inch stock.

On this page (10 sections)
  1. Will a Sawzall cut 1/4 steel, or does the blade decide?
  2. What blade cuts 1/4-inch steel best?
  3. How do you set up the saw for 1/4-inch plate?
  4. How long does it take to cut 1/4-inch steel?
  5. Which saw works for plate this thick?
  6. What about the blade set for mixed jobs?
  7. Do you need oil, and when should you stop?
  8. Is a Sawzall the right tool for this cut?
  9. What mistakes dull blades fastest?
  10. The short answer on 1/4-inch steel

Yes, a Sawzall will cut 1/4-inch steel with a bi-metal metal-cutting blade and a slow, steady stroke. It is thicker than the usual sheet metal job, so expect slower progress, more heat and more blade wear than on 1/8-inch stock.

The saw is not the limit here. Blade choice and technique decide whether the cut goes cleanly or burns through good blades.

Will a Sawzall cut 1/4 steel, or does the blade decide?

The blade decides. A reciprocating saw can run a metal-cutting blade through 1/4-inch plate, but a wood blade or a worn-out metal blade will stall, chatter and overheat.

A Sawzall is a demolition and rough-cutting tool, not a precision saw. It cuts plate, angle iron, pipe and channel well enough for home work, then you dress the edge with a file or grinder.

Teeth per inch is the first thing to match. The slower the blade cuts, the less heat builds in the steel and the longer the teeth last.

A blade pitched for thin sheet loads up with chips in a thick kerf, while a blade pitched too coarse grabs and chatters.

The steel itself matters too. Milwaukee lists The Torch blades for pipe, channel, tubing and angle iron up to 4 inches, so the same blade family covers the shapes a home job usually throws at you.

What blade cuts 1/4-inch steel best?

Use a bi-metal blade with a fine-to-medium tooth count made for metal. The Milwaukee Tool 6" 14 TPI The Torch is aimed at steel cutting, with 14 teeth per inch on a 6-inch blade.

Milwaukee describes The Torch blades as 1 inch tall for straight, fast cutting, with heat treating to extend blade life. The blade fits Milwaukee Sawzall saws.

That 1-inch height keeps the blade tracking straight in thick stock instead of flexing off line.

Fourteen teeth per inch is a good middle ground for 1/4-inch steel. It clears chips without the teeth riding too high in the kerf, and it holds up better than a fine 18 TPI blade on plate this thick.

The Torch also has the flex to work in tight spots where you cannot swing the saw freely.

How do you set up the saw for 1/4-inch plate?

Fit a sharp metal blade, set the shoe against the work and pick a low speed. A slow stroke on thick steel cuts cleaner than a fast one.

Clamp the steel so it cannot move or vibrate. A plate that bounces lets the teeth grab and can bend the blade.

On flat plate, clamp both sides of the cut line so the offcut does not pinch the blade near the end.

Mark the cut line, then start on an edge where the blade can seat. For a cut away from the edge, drill a starter hole first.

Set the shoe tight to the surface so the blade cannot wander. If you need a square edge, our guide on how to cut straight with a sawzall walks through the setup.

Starting the cut without a starter hole

If the blade must plunge into flat plate, tilt the saw and let the teeth bite at a shallow angle until the blade breaks through. Then straighten the saw and follow the line.

Never force a straight plunge; the tips strip and the blade skates.

How long does it take to cut 1/4-inch steel?

Expect minutes, not seconds. A short cut through plate takes a steady minute or two; a longer cut through angle iron or pipe takes several.

Running the saw flat out on thick steel builds heat, dulls the teeth and can warp thin sections. Push with light, even pressure and let the saw cycle on its own.

The stroke does the chip clearing, so a steady hand beats a hard shove.

If the blade stops moving forward, back off and check the tooth count. A blade that skates or burns is usually the wrong pitch or worn out.

Long cuts also drain a battery fast, so keep a spare charged and swap it before the last stretch rather than mid-cut.

Which saw works for plate this thick?

A brushless cordless saw has the strokes per minute to cut 1/4-inch steel, and the Milwaukee M18 FUEL Sawzall is the one to compare against.

The Milwaukee spec sheet puts it at 3,000 strokes per minute, powered by an M18 battery. It has a lever-actuated blade clamp for fast changes and an LED light on the cut line.

The light matters on plate because the kerf shadows the cut once the blade is buried.

It is a bare tool, so you need a charger and battery if you are not already on the M18 platform. The metal-reinforced battery connection is built to hold up to vibration over time.

A corded saw also works; the cordless model wins when the steel is bolted in place rather than on a bench.

What about the blade set for mixed jobs?

A mixed blade set covers the common home jobs if you cut wood, metal and demolition material with the same saw.

The DeWalt 12-Piece Bi-Metal Blade Set includes metal-cutting and wood blades in one case. The bi-metal construction gives the blade flexibility and a long cutting edge.

DeWalt credits the tooth forms with up to 50 percent longer life than its prior generation blades, and the tall, thick profile is built for straight cuts in heavy metal.

The set includes 6-inch and 9-inch wood blades, 6-inch 18-TPI and 8-inch 14-TPI metal blades, and one 9-inch 10-TPI demolition blade. The blades are Matrix II steel with 8 percent cobalt.

Picking the right blade from the set

For 1/4-inch steel, the 14-TPI metal blades are the ones to reach for. The 18-TPI blades suit thinner sheet and tubing.

The 10-TPI demolition blade is for nail-embedded wood and rough tear-out, not clean plate cuts.

Do you need oil, and when should you stop?

Oil helps on steel this thick, and you should stop when the blade stops cutting. Cutting oil cools the teeth and carries chips out of the kerf.

Apply a few drops along the cut line as you go. A cut taking more than a minute benefits most.

On plate, a thin stream is enough; flooding the cut just makes a mess.

Stop if the blade smokes, turns blue, or needs heavy pressure to move. Those are signs of heat, a dull blade or the wrong tooth count.

Swap the blade rather than forcing it. A fresh 14 TPI blade costs less than a damaged cut or a burnt-out saw.

Is a Sawzall the right tool for this cut?

It is for most home jobs, but not for every 1/4-inch cut. Rough cuts, pipe, angle iron and plate get done with a Sawzall and a metal blade.

For a long, straight cut where the edge has to be square, a cutoff saw or a grinder gives a cleaner result. For a quick cut in place, the Sawzall wins on reach and setup time.

If the material is concrete rather than steel, a different blade and saw setup is involved; see whether a reciprocating saw can cut concrete. For finer work, an oscillating tool is the other option, and it can handle some metal jobs; our guide covers whether an oscillating tool can cut metal.

Tile is a separate story, as our piece on whether an oscillating tool can cut tile explains.

What mistakes dull blades fastest?

Heat, wrong tooth count and a loose workpiece wear blades out faster than anything else. A bouncing plate grabs the teeth and bends them.

Pushing hard does not speed up a cut on plate this thick. It loads the blade and makes the motor work harder for the same result.

Starting the cut on a corner without a starter hole can strip the first teeth. Drill a pilot hole when the cut begins away from an edge.

Letting the blade ride in a wide kerf without support makes the cut wander. Keep the shoe flat and the plate clamped.

A blade that flexes sideways in the kerf wears its set down and starts to bind.

The short answer on 1/4-inch steel

Yes, a sawzall will cut 1/4-inch steel if you fit a bi-metal metal-cutting blade at around 14 TPI and keep the stroke slow. The saw handles the thickness; blade choice and technique decide how clean the cut is.

Pick The Torch blade for dedicated steel cutting, the Milwaukee M18 FUEL Sawzall if you want cordless power on the job, and the DeWalt 12-piece set if you cut wood and metal with one saw. Clamp the plate, add a little oil and let the teeth work.

If squareness matters, plan a finish pass with a file or grinder afterward.

Frequently asked questions

How thick is 1/4-inch steel in millimeters?

1/4 inch is about 6.35 mm. That matters because blade makers describe the steel they cut in fractions of an inch, while steel stock is often sold in millimeters.

Can a cordless Sawzall handle 1/4-inch steel?

Yes, a modern brushless cordless saw runs the same strokes per minute as a corded model and has the power for plate this thick. The catch is battery drain, so keep a spare on hand for long cuts.

Will cutting 1/4-inch steel ruin a good blade?

It wears it faster than thin sheet does, but a blade made for metal will finish the job. Keep speed low and let the teeth cut so the blade wears out from use rather than from heat.

Do I need cutting oil for this?

Oil helps on steel this thick. It cools the teeth, carries away chips and lets the blade run longer, especially on a cut that takes more than a minute.

Can I use a wood blade on steel plate?

No. A wood blade has coarse teeth and a different set, so it will grab, skate and overheat.

Use a bi-metal blade made for metal.